Bb-electronics ZZ-PROG1-USB - Datasheet User Manual download pdf

Zlinx Wireless Modbus I/O-0712ds page 1/5

www.bb-elec.com [email protected] [email protected]

International Office: 707 Dayton Road PO Box 1040 Ottawa, IL 61350 USA 815-433-5100 Fax 433-5104

European Office: Westlink Commercial Park Oranmore Co. Galway Ireland +353 91 792444 Fax +353 91 792445

PRODUCT INFORMATION B&B ELECTRONICS

Zlinx Wireless I/O

Peer-to-Peer and Modbus I/O

 Modular, Customizable Wire Replacement

 128 / 256 Bit AES Encryption

 Software Selectable RF Transmit Power

 Software Selectable Over-the-air Data Rate

 Modbus ASCII /RTU Compatible

 Wide Operating Temperature

 Active Repeater Functionality

 10 to 40 VDC & 24 VAC Input Power

Zlinx™ Wireless Modbus I/O - flexible enough to fit your

applications. These plug-n-play units from B&B Electronics

combine traditional Modbus RTU remote analog and discrete I/O

with built-in wireless connectivity. Wireless RTU serves as

Modbus slave RTU in radio-based SCADA systems, or as a

peer-to-peer communication platform.

Three Ranges Available - Short, Medium, Long range.

Active Repeaters - With built-in repeater functionality on -MR

and 900 MHz -LR models, you can ensure vital signals get

through.

Modular - Just snap on your I/O and you're ready to go.

Wide Temperature - Meets most indoor or outdoor applications.

Rugged circuitry prevents signal degradation.

128 / 256 Bit AES Encryption – Secures your data.

Selectable RF Transmit Power – Allows you to optimize the

transmitter power for your application.

Selectable Over-the-air Data Rate – Allows you to decrease the

OTA Data Rate on –LR and –LR-AU versions, effectively

increasing the radio transmitter’s range.

Exception Reporting – In Modbus mode, allows the reporting of

possible problems with connected devices.

Fail Safe – Allows you to set your I/O to a safe state in the event

of a communications failure.

Calibration – Calculates correction factors to make I/O values

better match your sensor.

Communications Failure Alarm – Allows the first DO to be

configured as a COM failure alarm indicator.

Invert Output – You can invert the logic of all DO’s in peer-to-

peer mode.

Monitor – You can use the Zlinx™ Manager Software to monitor

your I/O.

Wire Replacement (Peer-to-Peer Mode)

Replicate any analog or digital signal from a remote location-

Wirelessly! Use a pair of Zlinx™ Wireless I/O modules to read

sensor inputs or control actuators in hard-top-reach locations.

Inputs and outputs of the paired Zlinx radios will mirror each

other, making it easy to add wireless I/O to any application.

Modbus Peer-to-peer or Peer to Multi-peer

Seamlessly add wireless I/O to any Modbus application.

Modbus is the most widely supported I/O protocol worldwide.

With Zlinx Wireless I/O you can now bring wireless remote I/O

into any Modbus system. Simply connect a Zlinx modem to and

RS-232 or RS-485 port of the Modbus master and it can now

poll up to 150 wireless I/O nodes – each node can be

configured for 8 to 48 I/O points.

1 2 3 4 5

Summary of Contents

Page 1 - Zlinx Wireless I/O

Page 2 - I/O Points

Page 3 - Specifications

Page 4

Page 5

Comments to this Manuals

No comments

Bb-electronics ZZ-PROG1-USB - Datasheet User Manual

Browse online or download User Manual for Accessories communication Bb-electronics ZZ-PROG1-USB - Datasheet. B&B Electronics ZZ-PROG1-USB - Datasheet User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories communication Bb-electronics ZZ-PROG1-USB - Datasheet