Bb-electronics 850-14300--39 - Manual User Manual

iMcV-DS3/E3/STS Repeater Operation Manual

6 This feature can be controlled by SNMP management software (iView2) when the iMcV-DS3/E3/STS module is installed in a managed chassis.

7 Loopback Type This switch controls which data line is looped back when the Loopback DIP Switch is enabled. The data line loopback selection can be

8 This feature can be controlled by SNMP management software (iView2) when the iMcV-DS3/E3/STS module is installed in a managed chassis. ** WARNING **

9 DS3, E3 and STS Selection This switch selects the data rate to use on the coax line. The data rate selections available include the following: • 45

10 Remote Unit This option allows the user to enable Remote Unit on the module. The Remote Unit feature is designed to work only as the remote module

11 • Redirects the incoming signal back out to the origin while continuing to transmit downstream. • Blocks downstream data from arriving on the loope

12 Pseudorandom Bit Sequence (PRBS) Testing To test using Pseudorandom Bit Sequence, configure the iMcV-DS3/E3/STS modules for No Loopback, then conf

13 LED Operation The iMcV-DS3/E3/STS module features several diagnostic LEDs per port. The LED functions are as follows: LPBK NO LNK PBEO FA N

14 Troubleshooting General Troubleshooting • During installation, first test the fiber and BNC connections with all troubleshooting features disabled;

15 Specifications Power Consumption (Typical) 0.550 Amps @ 5 V Operating Temperature +32°F to +122°F (0°C to +50°C) Storage Temperature 0°F to +160°F

ii FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A computing device, pursu

16 B&B Electronics Technical Support Tel: (800) 346-3119 (in the U.S. and Canada) Monday-Friday, 7:00am-7:00pm CST +353 91 792444 (Europ

17 Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, whi

18 Electrostatic Discharge Precautions Electrostatic discharge (ESD) can cause damage to any product, add-in modules or stand alone units, containing

19 Safety Certifications UL/CUL: Listed to Safety of Information Technology Equipment, including Electrical Business Equipment.

International Headquarters B&B Electronics 707 Dayton Road Ottawa, IL 61350 USA Phone (815) 433-5100 — General Fax (815) 433-5105 Website

iii BUSINESS, LOSS OF USE OR OF DATA INTERRUPTION OF BUSINESS, LOST PROFITS OR GOODWILL OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAG

iv Table of Contents FCC Radio Frequency Interference Statement ... ii Limited Lifetime Warranty ... ii About the i

1 About the iMcV-DS3/E3/STS iMcV-DS3/E3/STS is an SNMP-manageable module which converts thin coax signals to single-mode or multi-mode fiber signals a

2 Requirements The iMcV-DS3/E3/STS is designed to conform to many DS3/E3/STS-based environments. Make sure that all of the relevant information about

3 iView2 supports the following platforms:  Windows 2000  Windows XP  Windows Vista  Windows 7 Please see the SNMP Management Module installa

4 Unmanaged Modules Before installing the module in an unmanaged chassis, including IE-MediaChassis series and MediaChassis series, manually configure

5 FUNCTION SWITCH SETTINGS RESULT [(D) = Default] Loopback (iView2 Configurable) S1-1: OFF Loopback Disabled (D) S1-1: ON Loopback Enabled